What is Flexo Microcell screening of CTP Laser Imaging
Nov 05, 2026
What is Flexo Microcell screening of CTP Laser Imaging?
What is the difference of Micro holes and CTP dots. The dot is a binary structure of "with or without ink" (with or without ink), while the micro hole is a continuous structure of "how thick the ink is" (digging shallow pits in areas where ink already exists). Changing from 100% to 95% of the outlets is to exchange "removing 5% of the ink" for "leaving 95% thicker"; The real micro hole mesh is to carve 90%+shallow pits in 100% of the area, and the total ink volume increases rather than decreases. This is the essential boundary between the first generation of local laws and the fourth generation of technology.
01. Microcell are not simply a type of halftone dot; they are an integrated system.
High-precision laser imaging, flat-top dot architecture, and plate surface engineering are all essential. Any claim that a RIP alone can generate microcell dots overlooks two critical physical processes: LAMS black mask ablation and UV exposure-based image formation.
02. Three different approaches achieve the same physical result.
Esko: Generates microcell patterns through direct file-based RIP screening, followed by laser energy-modulated imaging. Compatible with a range of plates.
Kodak: Applies a secondary microcell pattern to the screened dot file through a laminated mask micro-patterning process. Compatible only with its own plates.
XSYS: Applies secondary screening and engraving to the screened dot file through the imaging device. Compatible with a range of plates.
Final microcell structure: An array of micro-pits or grooves, 5–10 μm deep with a spacing of 12.7–18 μm.
03. Screening frequency determines the compatible anilox roller.
A frequency of 1,400 lpi (18 μm spacing) corresponds to an 800–1,050 lpi anilox roller, while 2,000 lpi (12.7 μm spacing) corresponds to an anilox roller of 1,000–1,200 lpi or higher. A mismatch between microcell frequency and anilox specifications can actually introduce ink streaking and uneven ink transfer.
04. Flat-top dots are a prerequisite, not an optional feature.
Creating microcells on rounded-top dots is like carving pits into a sloped roof: after plate washing, the cell walls may collapse and cell depth becomes difficult to control. Flat-top dots can be achieved through one of four approaches: flat-top plate technology, high-energy LED exposure, oxygen-removing lamination, or an inert-gas environment.
05. The ink system determines the maximum achievable benefit.
Solvent-based and water-based inks generally benefit the most. Conventional free-radical UV inks, due to their high viscosity and poor leveling, offer relatively limited improvement in solid-area ink density. Cationic UV inks, with viscosity potentially reduced to below 22 seconds under the specified measurement conditions, work particularly well with microcells and may enable a single white-ink pass to replace two passes.
06. Plate selection is more likely to be the wrong choice than equipment selection.
The plate must satisfy four requirements simultaneously: flat-top capability, a sufficiently smooth surface, compatibility between the LAMS black mask and imaging energy, and inclusion on the equipment supplier's approved plate list. A plate described as high-hardness or high-definition is not necessarily suitable for microcell production.
07. 2024 marked a turning point.
Quartz Edition advanced microcell technology from 1,400 lpi to 2,000 lpi, reducing spacing from 18 μm to 12.7 μm. Microcells consequently evolved from a solid-area enhancement technique into a surface-engineering approach applicable across the tonal range, from highlights to solids.
08. Acceptance testing must cover three stages, not density alone; appearance matters even more.
Quantitative criteria are required at all three stages: black-mask engraving, plate formation after washing, and final printing results. Measuring only solid ink density (SID) can miss the most critical defect: excessive microcell depth variation, which may cause progressive print-density loss along the production run.









